Boat Building Plans

For longer boats stations spaced 1100 until last at 1000

For longer boats stations spaced 1100 until last at 1000

Boat Building Plans

25 x 150 Length = 1000

Crosscleats at right angle to centerline string Check with plumb line

1 Corner of block must be on the mark for the building base on the transom

25 x 150 Length = 1000

Crosscleats at right angle to centerline string Check with plumb line

1 Corner of block must be on the mark for the building base on the transom

Tekne Resimleri
25 x 150 x 350

Bolt 10 x 120 Removable when turning boat over

The centerline on the transom must be aligned with the centerline string

Fix transom to blocks with 4 nails

Thickness = 50

  1. Place the middle frame on the building jig forward of the cross cleat. For the 5,2 m boat frame 2, for the longer boats frame 3.
  2. Align the frame vertically with a spirit level and horizontally to the centerline string with a plumb bob.
  3. Fix with 4 nails to the cross cleat.
  4. Brace the frame to thebuilding jig as shown.
Jig For Fix Tube
Centerline string

Align the forward frame on the building jig in the same way as the middle frame. Nail the frame to the building jig and support it to the ground, Place the stem on to the frame and align with the centermark on the frame,

  1. Stretch a line along the top of the building jig corresponding to the construction base. Check that this line meets the mark for the construction base on the stem.
  2. Fix the end of the stem firmly to the ground.
  3. Drill hole and bolt the stem to the frame.
Frame Building Jig

BUILDING JIG OMITTED FOR CLARITY

  1. Mount the remaining frames and connect them to the middle frame by two battens 20 x 50 temporarily nailed to the frames.
  2. Make cutout for the hog. See details below.

BUILDING JIG OMITTED FOR CLARITY

1. Mount the remaining frames and connect them to the middle frame by two battens 20 x 50 temporarily nailed to the frames.

Building Boat Frame

Fairing batten 20x44 Adjust bevel at transom and frame 1.

Check alignment with the stem, Adjust if required

2. Make cutout for the hog. See details below.

Fairing batten 20x44 Adjust bevel at transom and frame 1.

Check alignment with the stem, Adjust if required

Batten

Bevel

Batten

Bevel

Mark gap between batten and frame = bevel on a stick and transfer to the other side of the frame.

Fairing batten

Fairing batten

Do not cut below this line

It is best to have the hog in one length but in the longer boats a joint might be necessary.

Put bitumastic in joint

It is best to have the hog in one length but in the longer boats a joint might be necessary.

Put bitumastic in joint

Fao Boat Building

10x170

Bolts 10 x 100

10x170

Bolts 10 x 100

GUIDE FOR DRILLING Two persons checkiing by sight the direction of the drillbit before starting the drill

  1. Clamp a 16 mm plank to the frames near the chine. Mark bevel on the frames and transom. Remove the plank and cut the bevel.
  2. Clamp the plank back in place to check that it is in contact with the frames on the whole surface,
  3. Cut off the bevel at the stem gradually until the line on the forward side is reached, Adjust again the bevel on the forward frame.
  4. Repeat this process at the sheer.
  5. Draw a line between the bevel cuts and plane the complete bevel.
Boat Lines Plans

Line between bevel cuts

SIDEFRAME

Line between bevel cuts

SIDEFRAME

Boating Secrets Uncovered

Boating Secrets Uncovered

If you're wanting to learn about boating. Then this may be the most important letter you'll ever read! You Are Going To Get An In-Depth Look At One Of The Most Remarkable Boating Guides There Is Available On The Market Today. It doesn't matter if you are just for the first time looking into going boating, this boating guide will get you on the right track to a fun filled experience.

Get My Free Ebook


Responses

  • liisi
    How to make fairing batten?
    6 years ago
  • ines
    How to build intermediate bulk heads?
    6 years ago

Post a comment